Business Opportunity Details


FNT-BIZ-B/01: Available Steel Plant for sale in Orissa
The integrated Steel Plant comprises of Raw Material Handling Plant, 325 TPD (DRI) Direct Reduced Iron Plant, 1 X 12.5 MW Captive Power Plant, 4 x 7 + 1 x 8 Tons Steel Melting Shop (SMS), M S Ingots 1,20,000 Tons, and other auxiliaries like water treatment plant.

* The Running Steel Plant is situated in the State of Orissa.
* Total Area of Land: 94 Acres
* The details of Steel Plant attached herewith for your necessary action

* The Sale Price of the said Plant is fixed Rs.235 Crore (Non-negotiable).
* Interested BUYER kindly forward your LOI to the undersigned.
* Your early action on the above subject will be highly solicited.

If interested contact the undersigned at DYNET ONLINE TECHNOLOGIES, Mr.Dharmaprakash M Shettigar 022-25792364 / 09757302384 / 09619562806, Email: fntindia@hotmail.com

 Back | Top

FNT-BIZ-B/02: A Cement Factory in Tamil Nadu for sale
The below given proposal was forwarded by a Consultant ASHOKAN. Installed capacity is around 500 MT and expansion plant under installation, so total capacity is around 1450 MT. The expansion project would be completed in Oct / Nov 2010.
  • About 25 acres of land around plant.
  • Present capacity - 500 MT/day.
  • Main Equipments: 1) Raw Mill * No.1 * capacity * 30MT/hr.
  • Raw Mill * No.2 * capacity * 40MT/hr.
  • Vertical Shaft Kilns * 3 nos. * capacity * 150MT/day.
  • Vertical Shaft Kiln * 2 nos. * Capacity * 200MT/day.
  • Cement Mill * No.1 * capacity * 25MT/hr.
  • Cement Mill * No.2 * capacity * 35MT/hr.
  • Crusher * Primary & Secondary - capacity 125MT/hr
Equipments are in good condition, running from November 1997, but Raw mill No.2, Cement Mill No.2 and 2 Vertical Shaft Kilns installed during April 2005 to March 2006.

Taken up expansion to install following equipments.
  • Rotary Kiln 900TPD of Clinker.
  • Crusher cum Dynamic separator for Raw Mill Section.
  • Crusher cum Dynamic separator for Cement Mill Section.
The capacity after expansion will be 1100 - 1200 MT of Clinker, i.e., new Rotary Kiln ? 900 TPD and existing Vertical Shaft Kilns can be run to produce up to 200-300 MT of clinker based on Raw Mill capacity. Cement production will be 1450MT/Day with 30% addition of Fly Ash. (1100 x 1.30).

Total cost of installation of above expansion is Rs.65 Crore. We have got bank sanction for a term loan of Rs.57.87 crore. We have also applied to Tamilnadu Pollution Control Board and also completed the initial hearing at State Level Environment Impact Assessment Authority(SEIA) . SEIA has also approved our project. We are in the process of finalising, suppliers and placing Orders. We have given advance to some long delivery items. We have started civil works. Total limestone required for expanded capacity will be 6 lakhs MT per year. We will provide a limestone area with Reserves of 15 million MTs i.e., for 25 years requirement or supply limestone on long term agreement for 25 years.

If interested contact the undersigned at DYNET ONLINE TECHNOLOGIES, Mr.Dharmaprakash M Shettigar 022-25792364 / 09757302384 / 09619562806, Email: fntindia@hotmail.com

 Back | Top

FNT-BIZ-B/03: A Running 45-room Hotel Near Anjuna Beach, North Goa For Sale
  • The core business of the current owners is construction and this was one of their projects. This hotel was set-up in 1995. We are running this as hotel for the last thirteen years. The hotel is 500 metres from Anjuna beach.
  • The Total Plot Area is 3050sq. mts. The land is free-hold land.
  • The Built-up Area is 2500sq.mts. approx.
  • Most of the units/rooms were sold to different parties and inturn, these same units were taken on 'Rent Back Scheme' by us on per month rent basis. This was in 1995 to begin with and subsequently the leases were renewed every three years and the latest lease agreement is valid till 2010, which is to be renewed by the new owners with our assistance if needed.

    The present rent paid by us is Rs.4500/month for six months and next year it will be Rs.5000/month as ten percent increase for five months (Nov-March).

    Our guests are about 80 percent foreigners and NRI's and twenty percent Indians.
  • We have not sold all the units/rooms to others. We have retained about 10 room units plus the commercial block building, plus the swimming pool and all plant and machinery, parking lot, gardens etc.
  • We have all the licenses dating back from 1995 from Excise dept, Tourism dept, Labour, ESI, PF, Reserve Bank, Luxury Tax, VAT, Panchayat, Food and Drugs, Shops and Establishment, etc.
  • We are now looking for a new party, preferably with hospitality industry experience, and owning/running other properties across India, to take over the property.
  • We are selling our real estate assets in the hotel plus the 'Hotel business' i.e. transfer of hotel business and lease etc completely. The hotel will be sold as a going concern.
  • The Expected Price is Rs.3.50crore. You get our share of assets and the Hotel business along with lease.
  • We have some good staff employed who have been working with us for ten years and more and we are keen that they will be settled properly by us, and the new owners too.
  • If the new owners so desire it is also possible to 'Buy Outright' all room units for approximately Rs.8crore. The approximate cost of room units is Rs.10lacs and Rs.8lacs respectively for one bed kitchen room type and one room kitchen type. All are apartments.
  • So we are in the lookout for a party, preferably experienced hotelier, who wants to add a Goa property to his properties or an investor.
  • The reason for the sale: The current owner is going overseas permanently.

 Back | Top

FNT-BIZ-B/04: Joint Venture / Private Equity Partner required for Industrial Solders & Aluminium Alloy Ingots Company in Chennai, Tamil Nadu
  • Brief Profile of the Company:
    • It is a 23year old ISO 9001:2000 company engaged in the manufacture of Aluminium Alloy Ingots, Aluminium Castings, Zinc Castings, Aluminium Extrusions, Aluminium Profiles, Industrial Solders, Fluxes, etc., in the SME segment.
    • The present turnover is Rs.15crore, with a projection of Rs.30crore for the year 2008-09 with the existing facility.
    • They are now looking for a prospective Joint Venture Partner / Private Equity Partner to augment the existing facilities and working capital requirements, since their core business activity revolves around automobile components / construction industry, which is extremely doing well.
    • In this connection they require an amount of Rs.12crore towards Joint Venture from genuinely interested parties. They are also open to private/public equity.
    • The company was incorporated in 1995 with the main aim of starting a manufacturing unit of Industrial Solders and Aluminum alloys. Mr. T.R.Viswanathan and S.Swaminathan and others promoted this company.
    • Promoters started the business of Industrial solders as a proprietary concern in the year 1985 later they converted it in to a Private limited company and has own manufacturing facilities at 3 locations.
    • The company is producing the following major products i.e. Aluminium Alloys Ingots, Aluminium Profiles, Aluminium Castings and Aluminium Machined Components.
    • The products are used in the auto component industry, construction industry and bus body building units of mostly state government transport corporations.
      PRODUCTION DETAILS
        Production for Last Three Years Production Proposed for next three years
      Products 2003-04 2004-05 2005-06 2006-07 2007-08 2008-09
      Alloys 417 MT 835 MT 1035 MT 1500 MT 2400 MT 3600 MT
      Profiles 13.5 MT 82 MT 178 MT 250 MT 1200 MT 2400 MT
      Solders 40 MT 15 MT 5.4 MT 10 MT 20 MT 30 MT
      Castings - - - 100 MT 600 MT 1200 MT
  • Plant & MAchinery:
    The existing units have the following machinery like 375 ton extrusion press, 4 & 2 ton capacity rotary furnace for making alloys, 2 crucible type furnaces to manufacture billet/ casting. Company has a well established laboratory set up equipped with state of the art CCD Technology based optical emission spectrometer. Company has got 5HP air Compressor, 20 KVA & 62.5 KVA Generators.
     
    The company has added additional machinery like 700MT Press + Installation, Billet Cutting Machine, Billet Heater, Ageing Oven, Finish Cutting, Nitriding Furnace, Air Compressor, Bale Out Furnace.
  • Power:
    At all the premises, already an existing connected load of 300 HP under LT supply is available, which is sufficient for the existing machinery and its operations.
    To take care of the power cut, already an existing Diesel Generator of 20 KVA and 62.5 KVA capacity is installed at the premises. Company is planning install 2 diesel generator of 125 KVA each.
  • Water:
    Apart from the normal supply of water from the Board, bore well available in all units.
  • Fuel:
    The units are presently running on LPG.
  • Applications of Aluminium and its Alloys in the Automobile, Defense and Aviation Sectors - Aluminium alloy is used extensively in the auto industry and as more aluminum is used per vehicle, the pool of scrap aluminium is bound to increase to as the metal in these vehicles eventually enters the supply chain after they have been scrapped. Many alloys are produced from scrap or recycled material, which makes it an extremely environmentally friendly metal, which is likely to grow in size. Similarly aluminum and steel forging products are widely used in aviation and defense sectors.
  • Applications of Aluminium Extrusions in the Construction and Transport Sectors - Aluminium extruded, rolled, and cast products are commonly used for window frames and other glazed structures ranging from shop fronts to large roof superstructures for shopping centers and stadiums; for roofing, siding, and curtain walling, as well as for cast door handles, catches for windows, staircases, heating and air-conditioning systems. Most recently, aluminium has played a significant role in the renovation of historic buildings. The characteristics and properties of aluminium as a material have lead to revolutionary and innovative changes in building techniques and architectural and engineering projects. Aluminium is leading the way into the future of the construction industry. Aluminium extrusion is used extensively in the transport sector to frame the bus bodies.
  • The Current Market Trend
    Aluminum Alloys and Extrusions play a major role in industrial and commercial sectors. The success ratio will definitely be large as aluminum alloys and extrusions cater to almost all industrial and commercial sectors.
     
    Many Automobile giants like Hyundai, Ford, Hindustan Motors, Ashok Leyland, TVS and BMW are situated in Chennai.The requirement for Aluminium alloys are around 7000 MT per month. The current market trend for aluminum extrusions is around 700MT per month.
  • SWOT:
    1) Strength: 25 years of alloying experience + skilled Work force + reputed Customers + boom in Auto Component sector + Company located in the Detroit City of India (i.e. Chennai).
    2) Weakness: Lack of Financial Support.
    3) Opportunity: Almost all World Auto Majors are focusing on India and China + Ideal climatic conditions for foundry operations + Very good Infrastructural facilities.
    4) Threat: No major threat envisaged than heavy rains.

Kindly study the same and let us know your interest at the earliest.

Click here to read the complete Investment Proposal.

If you wish to go for a plant visit, kindly forward the MANDATE LETTER on your Company Letterhead accepting the Terms & Conditions of the Consultancy. Click here to download the MANDATE LETTER format.

 Back | Top

FNT-BIZ-B/05: A running Mineral Soda manufacturing company in North India for Sale or Take-over
  • The Company is India's one of the leading manufacturers of Carbonated Mineral Water pioneering the concept of PET bottle soda.
  • The Company was founded by two enterprising entrepreneurs with a novel concept of Mineral Soda in PET bottles.
  • The Mineral Soda was launched in 1998 when all major players in the market were using glass bottle for soda.
  • With 160 distributors and 7 Clearing and Forwarding Agents spread over 7 States viz. Punjab, Haryana, Himachal Pradesh, Jammu & Kashmir, Rajasthan, Uttar Pradesh, Uttaranchal, National Capital Territory of Delhi and Union Territory of Chandigarh, the Company claims to be the largest selling mineral soda company in North India.
  • In order to meet its requirement for PET Performs used for bottles and CSD Closures, the Company decided to develop an in-house import division instead of relying on the local suppliers.
  • Generally, soda is made from ordinary or filtered water but this brand is made from the water that is treated to make it low in TDS (Total Dissolved Solids) by removal of undesired hard minerals. It is then blended and chilled for effective carbonation. The carbonated water is then filled into bottles.
    The supervisor checks the quality of soda by maintaining the pressure of CO2 and also by tasting the soda. Soda bottles are then inspected through illuminated light to check for any kind of impurity that might have moved in to the liquid. Bottles, after inspection, are capped. The bottles are then tested for leakage and are sent to the soaking bay where they are kept for at least 72 hours for any kind of deformity, leakage, ballooning, bursting. Thereafter, the bottles are labeled. The labeled bottles are kept in trays for shrink-wrapping.
  • From a single member family, the Mineral Soda brand today has grown to a tribe of big and small members: Party 1.5 litre, Jumbo 2 litre, Mini 400 ml, Regular 600 ml.
  • With a view to exploring new possibilities, the innovative leaders of the team have now introduced a flavoured Mineral Soda brand without sugar.
  • No deposit to retailer for the safe return of bottle as is the case for glass bottles.
  • Disposable nature of product makes it the most convenient companion of travelers who had either to wait at some place or deposit the security.
  • PP Caps have replaced crown caps making it easier to recap the bottle for reuse again.
  • Corrugated trays along with shrink pouch replace wooden or plastic crates and are disposable in nature.
  • Because of throwaway nature, and new bottle sourced every time makes it is easier to control the impurities.
  • Composite, which means land, building, plant and machinery on 'as-is-where-is-basis'. The area of both factories are 2000 sq.yards and the built-up area details are 3600 sq. ft. office and with RCC and 6100 sq.ft. in shed. The expected price is Rs.1.5 crores inclusive of all present liabilities of the firm etc. or Rs.1.30 crores without bank and hidden liabilities.
  • Only Plant and Machinery where the expected price is Rs.90 lacs. The detailed list of the PLant and Machinery will be sent on request.

 Back | Top

FNT-BIZ-B/06: A 2 X 50TPD Sponge Iron cum Steel Ingots Manufacturing Plant at Jamshedpur for Sale or Acquisition
  • 2 X 50 TPD Sponge Iron Plant of TGS & B.K.Engineering-make is in excellent running condition. Similarly the Induction Furnace of Electrotherm-make for manufacture of Ingots is also in running condition with full capacity utilization.
  • Sponge Iron unit was commissioned in the year 2000 and Ingots unit in the year 1997.
  • Sponge Iron unit is having Coal Linkage with CCL for 38,400MT p.a.
  • Power supply connection for both the units is arranged from Jharkhand State Electricity Board and the power supply in Industrial Area is excellent.
  • Both the units are complying with Pollution norms to the satisfaction of the Board officials.
  • Both the units do not have any Term Loan liability with any financial institution. Only Cash Credit limits against inventories are availed.
  • No other Government or statutory liabilities exist for both the units.
  • Sponge Iron Plant has a concrete road for movement of vehicles & materials handlings.
  • As our Group is engaged in major expansion programme in other region, full attention could not be paid to these well-run units for the sustenance of excellent performance hence are being disposed off.
  • Both the units are ideally located for procurement of Raw Materials supported with other infrastructural facilities essential for any unit to operate soundly.

Click here to download the list of Plant & Machinery.

The proposed Sale price of both the units together is fixed at Rs.17 Crores.

If you wish to go for a plant visit, kindly forward the MANDATE LETTER on your Company Letterhead accepting the Terms & Conditions of the Consultancy. Click here to download the MANDATE LETTER format.

 Back | Top

FNT-BIZ-B/07: A 200 TPD Sponge Iron Plant & 8MW Power Plant in Bilaspur, Chattisgarh For Sale or Take-over

The integrated steel plant (2 X 100 TPD Sponge Iron unit with 2 x 4MW Power Plant is located in Bilaspur, Chattisgarh.

  • Location of the plant - between Raipur & Bilaspur in Chattisgarh
  • Total land area - around 150 acres
  • Compound wall 75% completed for 55 acres
  • Sponge Iron Kilns - 100TPD x 2 (Commissioned between 2002 & 2005)
  • Power Plant 8 MW (Generate 4 MW with 2 Nos. of WHRB at present)
    Ø WHRB Thermax make 12.5Tons x 2
    Ø Turbine Triveni make 8MW
    Ø Complete Electricals & other infrastructure for 8MW Generation.
  • Infrastructure - Furnished Administrative Building cum control room. Store Bldgs, Workshop, Raw Material sheds, Sponge shed, Security building, time office, Quality Control building etc.
  • Sufficient Water in Bore Wells.
  • Hard Strata of Soil.
  • Railway siding about 21 Km from plant.
  • Gensets - 2 Nos. of 500 KVA & 1000 KVA each.
  • 800 KVA connected load (provision to expand).
  • Coal Linkage obtained for 2 Kilns.
  • Company had applied for allotment of Coal Block for its captive consumption, which was evaluated & a Coal block was allotted.
  • Unfortunately on exploration it was found that the allotted Coal block was not mineable due to meagre deposits. Hence as advised by the MOC the said block was surrendered and a fresh application was submitted.
  • The meeting of screening committee was scheduled to be held on 17.12.2007 to consider & allocation of the applied blocks, but meeting was postponed due to the reasons best known to Ministry. Being a bonafied allottee & as assured by the MOC, Company is confident to get a fresh block allotted in the meeting may be held at any time within a month.
  • Eligible for Carbon Credit for 4 MW waste heat Power plant.
  • MOU with Chattisgarh Government signed to become a pure integrated Steel Plant with 34 MW Power.
  • Ample land is available and can be further procured for expansions.
  • Head Office is connected with the plant through Internet.
  • Advantages:
    >> It takes 2 years to start from scratch (ground-up). So you save the 2 years of gestation period.
    >> Now Banks do not 'FINANCE' any new Sponge Iron Projects.
    >> No Distress Sale / No Finance Problem.

Kindly study the same and let us know your interest at the earliest. The above proposal has been forwarded to us by a CONSULTANT Mr.R.K.Singhania

If you wish to go for a plant visit, kindly forward the MANDATE LETTER on your Company Letterhead accepting the Terms & Conditions of the Consultancy. Click here to download the MANDATE LETTER format.

 Back | Top

FNT-BIZ-B/08: A Running 300 + 50 TPD Sponge Iron unit at Bhillai in Chattisgarh For Sale or Take-over
  • Land - 15 acres of land covered with bricks & column boundary wall - 3 Mtr height all around.
  • Rotary Kiln
  • Cooler
  • DSC
  • ABC
  • Wet Scrapper below DSC
  • Coal Crusher
  • Iron ore crusher
  • Separation building (Having RCC structure)
  • Product House - Having RCC structure and covered with G.I. Sheet.
  • Stock House - having R.C.C. structures and covered with G.I. sheet.
  • Raw Material Handling arrangements.
  • Iron ore washing arrangements.
  • Diesel Generators
  • Air compressor
  • Pump House
  • Machine Shop
  • Earth Moving Vehicles
  • Weigh Bridge
  • Administrative Building - Constructed area 3600 Sq. ft.
  • STORE - R.C.C. Building constructed area 10000 sq. ft.
  • Pollution Control Equipments
  • Coal storage shed
  • Electrical load
  • Electrical sub station

Click here for a complete list of plant & machinery.

Kindly study the same and let us know your interest at an earliest. The above proposal has been forwarded to us by a CONSULTANT Mr.R.K.Singhania.

If you wish to go for a plant visit, kindly forward the MANDATE LETTER on your Company Letterhead accepting the Terms & Conditions of the Consultancy. Click here to download the MANDATE LETTER format.

 Back | Top

FNT-BIZ-B/09: A Running 300TPD Sponge Iron Plant cum 65TPD Pig Iron Plant in West Bengal for Sale or Acquisition
  • The Plant site is ideally located on NH-32 geographically suited with excellent infrastructure.
  • The total area of the plant site under our possession is 40 acres of land with well-constructed boundary wall all around. Enough area is available for carrying out plant expansion & diversification.
  • Presently Sponge Iron Plant of 2X100 TPD capacity is in operation with ESP and ECMCS facility to the satisfaction of Pollution Control standards. 1st 100 TPD kiln is of BK Engineering make, 2nd & 3rd 100 TPD kilns are of Hari Machines Ltd., the 50% of the kiln & cooler assembly for the 3rd kiln are lying ready with us, as the foundation work is completed & almost 50% of other equipments for 3rd kiln are also procured & lying with us.
  • 65 CuM capacity Mini Blast Furnace in operation is producing Pig Iron with GCT as per the Pollution Standards. Civil foundation work is complete for setting up 2nd 65 CuM capacity Mini Blast Furnace except the main furnace foundation.
  • Sponge Iron Plant commenced productions in the year 2004 and Pig Iron Plant commenced productions in the year 2005.
  • Energy supply connection is from West Bengal State Electricity Distribution Co. Ltd. For Sponge Iron Plant 750 KVA power supply is available. For Pig Iron Plant 900 KVA power supply is available but 1000 KVA sanction accorded. DG sets of 380 KVA and 650 KVA for Sponge Iron Plant & 1250 KVA & 1000 KVA for MBF Plant are available.
  • Both the plants are new; all the equipments are in excellent running condition with adequate stock of essential spares. As such Refurbishment / Up-gradation doesn't arise for the present.
  • As the plant site is strategically situated for in-warding of raw materials and the area as such is peaceful falling under 'C' Group categorized by Industry Dept. of West Bengal, many concessions and facilities from the Government have special provision for this site. In-warding of raw materials and out-warding of products have no constraints and commercially viable & economical.
  • Coal linkage is under active consideration with the Ministry of Coal and the linkage order is expected shortly.
  • Two-storied Building for staff quarters with an accommodation capacity for 200 persons are available. Similarly well-constructed two-storied Administrative Office Building is also available and a gracious temple complex, bore well water facility to meet the water requirement is available.
  • Further we have obtained GO issued by Commerce & Industries Department for the Megha Project to set up Induction furnace, Re-rolling Mill & even captive Power Plant on the land available.
  • Both the Units are registered with all concerned Government registering authorities with updated status.

Click here for the list of Plant & Machinery.

Kindly study the same and let us know your interest at the earliest. The above proposal has been forwarded to us by a CONSULTANT Mr.D.Sanganee.

If you wish to go for a plant visit, kindly forward the MANDATE LETTER on your Company Letterhead accepting the Terms & Conditions of the Consultancy. Click here to download the MANDATE LETTER format.

 Back | Top

FNT-BIZ-B/10: A running profitable Aluminium Casting unit in Ambala, Haryana for Sale or Acquisition
  • The unit is into manufacturing of Aluminium casting parts supplies are to leading Automobile Companies of India.
  • The unit has also been exporting to European and American Companies for the last many years.
  • The unit was established in 1992, and is ISO: 9001: 2000 Certified.
  • The factory is located near Ambala, Haryana.
  • The total land area is 4840 sq.yards, and the covered area is 15000 sq.ft. (approx).
  • The techniques used in Aluminium casting are Low pressure Die-Casting, Gravity Die-Casting, and Sand Casting.
  • The installed capacity of the unit is 2000 Kg/ Shift, and a load of 49 KW is sanctioned.
  • The unit specializes in manufacturing all kinds of critical and non-critical cast Aluminium parts.
  • The foundry is backed by an in-house tool room with CNC Machining, which are duly supported by the best available software, enabling 3-D (CAD) parametric modeling, mould/ die designing and mould/ die manufacturing (CAM).
  • The unit offers the facilities of complete machining as well as desired assembly of components (as per customer's requirement).
  • This unit is best suited for buyers willing to invest in a business involving regular orders and low marketing efforts.
  • Reasons for Selling the Business - Seller intends to immigration to Canada and plans to move next year. He intends to set up his International Marketing Business, to be operated from Canada. This can help the current unit in getting enormous export orders.
  • Why you should buy this business?
    • Repeat orders are the biggest advantage of this business. The intake of even one single buyer is so huge, that if one keeps on supplying quality goods and provides timely delivery to the buyer, there is no need for a wide-scale marketing. This unit is already supplying to leading buyers, and orders are ongoing. The potential is so huge that the turnover can be increased to more than Rs.20crore (by using the same infrastructure).
    • The unit is a regular supplier to a few foreign firms. These buyers are from European countries, Canada, and USA.
    • The owner intends to establish his International Marketing Consultancy once he moves to Canada. This can definitely help to boost the export market of this unit. Export orders usually get decent profits.
    • Since buyers are leading names in the Industry, payment terms are fixed (45-60 Days), and the payment is secure.
    • The Business is order-based, and there is never a problem of over or dead Inventory.
    • If one were to establish a new unit today, the investment would be much more than the asking price.
    • The unit has a decent goodwill in the market, and orders will never be a problem. The seller assures full cooperation to the buyers in further strengthening the domestic market.
    • The production involves a particular level of skill. Seller assures full support to the buyer in providing complete technical know-how as well as training. Owner is involved in this business for more than 15 years, and he is willing to share all the fine points of business with the buyer.
  • The asking price for the complete unit is Rs.4.40crore.
    • Land (4840 sq yards, near Ambala) : Rs 1.50 crore
    • Building (15,000 sq ft) : Rs 0.96 crore
    • Machinery list can be provided at a later stage : Rs 1.11 crore
    • Dies, Moulds, Tooling, Jigs and Fixtures : Rs 0.35 crore
    • Goodwill : Rs 0.48 crores
  • Current Financial health of Business
    • The Sales in 2007-08 were Rs.2.32 crore, and the net profit was Rs.23.5 lacs.
    • The Sales in 2006-2007 were Rs.3.02crore, and the net profit was Rs.18.14 lacs.
    • In the current financial year, the unit has already achieved sales of around Rs.1.5crore (Till 31st August 2008).

      If some more working capital is pumped in this business, the present installed capacity can give sales upto Rs.20crore, and net annual profits of around Rs.2.5crores can easily be generated.
  • Justification of Goodwill - Owner has put in more than 15 years of hard work to establish the business. It takes years to build a reputation, and to win the trust of leading buyers. The unit on date is supplying to leading names in the Industry. Also, the unit is earning a net profit of around Rs.23.5 lacs. It may take years for a new manufactures to reach this stage. Thus a business goodwill of Rs.48 lacs (which is around two years of net profit) is justified. Complete technical know-how, existing clients, marketing support for next few months is included in this figure. The buyer will enjoy the luxury of having orders in hand from the very first day of starting his business.
  • Domestic Buyers - The firm supplies to leading Tractor manufacturers of India. If some more Working Capital is pumped in to this business, getting twice or thrice the amount of orders from buyers will not be a problem.
  • Exports - The unit has direct exports to the following countries:
    · The Netherlands, · USA, · Canada

If you wish to go for a plant visit, kindly forward the MANDATE LETTER on your Company Letterhead accepting the Terms & Conditions of the Consultancy. Click here to download the MANDATE LETTER format.

 Back | Top

FNT-BIZ-B/11: A running Petro-Chemical (Ethanol & Specialised Chemicals) Manufacturing Unit for sale in Satara, Maharashtra
  • The Expected Price for the complete infrastructure (Land, Building, Plant & Machinery) along with all the licenses & approvals = Rs.3.35 crore.
  • The company is a running Petro-Chemical (Ethanol / Specialised Chemicals) manufacturing unit located at Satara in Maharashtra. The manufacturing plant is located at Satara in Maharashtra.
  • The Raw material for Ethanol would be Specialized Denatured Spirit (R.S).
  • For manufacturing the Specialised Chemicals the raw material will vary according to the products and for Specialized Solvents raw material is purchased from GAIL India L.T.D.
  • The Ethanol Manufacturing unit is in SS-304. The capacity is 9lakh Litres per Month, (This includes all the P/M related to Ethanol, Storage capacity of 10lakh litres of Ethanol, Boiler (mfr by Elite Thermal 3 ton 10 kg Pressure baggase fired). The Plant and Machinery are in very good condition.
  • The second manufacturing plant is a Multi-utility Chemical Plant. It is in SS-316, (This includes P/M related to MUP, 3lakh litres storage capacity, Furnace Oil Boiler 4 Kcal). This plant is just a year old.
  • In the Multy-utility plant the following Specialized Chemicals/Products are manufacture:
    Distillation of
    Acetone DME DMF IPA
    Perfumery Products
    Benzyl Acetate Benzyl Alcohol Butyl-cello solves Acetate -
    Bio-Diesel
  • Land Area is 11925 Sq.Mtrs. (approx. 3 acres)
  • Bank: No Objection Certificate (NOC) or any other Permission required for sale or takeover shall be given after the primary discussions are over. We already have bank's verbal approval for the same. Every formality shall be completed after the bank's approval.
  • We have Bank liability, so we shall fulfill / clear all the conditions / liabilities of the Bank before we proceed further. We shall take care that the BUYER get a clean Company if he decides to Buy / Acquire / Purchase / Take over.
  • The Asking Price is inclusive of all the licenses stated below:
    No. License Details
    1 I.E.M (Industrial Entrepreneur Memorandum)
    1 Ethanol Manufacturing License
    3 S.D.S Storage License
    4 Factory Act License. (Under validation)
    5 Solvent 2007 (Under Renew)
    6 Explosive License
    7 Pollution Consent to establish is available and Consent to operate is under process
    8 High Court order to sell; buy Ethanol or Denatured Spirit to any Customer.

Click here to download the list of Plant & Machinery.

If you wish to go for a plant visit, kindly forward the MANDATE LETTER on your Company Letterhead accepting the Terms & Conditions of the Consultancy. Click here to download the MANDATE LETTER format.

 Back | Top

FNT-BIZ-B/12: A new unused Anhydrous Ethanol Manufacturing unit at Patalganga, Raigad, Maharashtra for Joint Venture/Sale
  • Land Area - 2.25 acres.
  • The unit is located next to Reliance Rasyani, Patalganga, Khopoli.
  • The ethanol manufacturing unit has a capacity of 50000 liters per day with all licences and approvals.
  • Molecular seves based D.C.S system.
  • Storage capacity 17 lakh liters.
  • Asking Price for Plant & Machinery only would be Rs.1.15crore.
  • Asking Price for the complete manufacturing set-up i.e. Land, Factory Building, Plant & Machinery is Rs.4.5 crore.

Click here to download the list of Plant & Machinery.

If you wish to go for a plant visit, kindly forward the MANDATE LETTER on your Company Letterhead accepting the Terms & Conditions of the Consultancy. Click here to download the MANDATE LETTER format.

 Back | Top


 


Back  Top
A A A
Custom Search
Email your queries
Name:


Email ID:



 
*Enter Security Code: (as shown below)
Web Form Code